Rinnai HD70e Uživatelský manuál

Installation and User Manual Infinity 32e and HD70eInfinity 32e and HD70e Continuous Flow Water Heater Important. Read these instructions carefully b

10TECHNICAL DETAILS Infinity Model Infinity 32e HD70eUnits Installation ExternalExternalNat Gas Press Low 1.8 1.8 mbarNat Gas Press High 7.4 7.4

11Congratulations on purchasing the Technologically Advanced, Temperature Controlled,Rinnai Hot Water System. • The Rinnai Infinity 32e and HD70e NEVE

12Excessively hot water is dangerous, especially for young children and the infirm. Thewater heater allows you to control the temperature of your hot

13IMPORTANT INFORMATION Always check water temperature beforeuse.Refer to warning about hot water onpage 12 for important safety information. Hot wate

Te14

15 TEMPERATURE CONTROLS - GENERAL When deciding on the best position for the temperature controls, the following points should be taken into account.

16 TEMPERATURE CONTROLS - INSTALLATION Universal Temperature Controller MC-91-1A 1. Determine the most suitable position for the temperature control

17 TEMPERATURE CONTROLS - INSTALLATION Connecting One or Two Controllers 1. Isolate the power supply. 2. Remove the front cover from the Appliance (4

18 TEMPERATURE CONTROLS The purpose of a Temperature Controller is to enable the user to have complete control over the hot water supply. Used correct

19 Remote temperature controllers are a feature that provides control over the water temperature. Rinnai Infinity and HD water heaters can be operate

2RINNAI UK WARRANTYAs the purchaser of this high quality Rinnai Water Heater you are provided with the following conditional guarantee. Defini

20 TEMPERATURE CONTROLS - OPERATING Using 1 Universal Temperature Controller. Press the On/Off button on the temperature controller. The ON

21 Using 2 or more Universal Temperature Controllers. Switching the system ON. Using hot water. Bathroom temperatures

22 Using 4 Universal Temperature Controllers. You will need to activate the fourth controller. STEP 1: STEP 2:

23 Using High Temperature Display Controllers. You will need to program the Master controller if you want to display and use temperatures over 500C.

24 Note To turn off your hot water system. Additional safet y features. During normal operation the system

25 TEMPERATURE CONTROLS - INFORMATION Do not push the On/Off button on the Master controller after transferring priority of temperature selection to a

26 TESTING 1. Purge gas, hot water and cold water supply lines before making the final connection of the water heater. Swarf in either the gas

27 GAS PRESSURE SETTING The working gas pressure on the water heater is electronically controlled and factory set. Under normal circumstances it do

28 GAS PRESSURE SETTING 11.Adjust the regulator screw on the modulating valve (fig. 4) as required to the pressure below. 12.Lock the regula

29 DIP SWITCH SETTING Dip Switch Positions Explained OFF ON SW2 1 - Gas Type LEGEND: 2 - Gas Type Black Section indicates 3 - Tem

3CONTENTS Unpacking Rinnai Water Heater.……………………………………………………………Installation Instructions………………………………………………………………………Flue Requirements...………………………………………

30DIP SWITCH SETTING Infinity 32e and HD70e Temperatures - Remotes Connected off on SW2off on SW2off on SW2off on SW2 1 1 1 1

31ERROR MESSAGES Rinnai water heaters have the ability to check their own operation continuously. If a fault occurs, an error code will flash on the D

32 ERROR MESSAGES Troubleshooting without controllers If you have not installed temperature controllers and experience the following symptoms, please

33 RESTARTING THE RINNAI WATER HEATER Following a power cut the heaters should be restarted in this manner. Standard system. Single or multiple water

34 WIRING DIAGRAM

4UNPACKING RINNAI WATER HEATER • After unpacking the appliance check for damage, if the heater is damaged contact your supplier immediately. Do not i

5IMPORTANT INFORMATION 1. Gas safety (Installation & Use) regulations 1998 are the ‘Rules in force’. In your own interest and that of safety, it i

6General Installation Information. External Installations. The Rinnai Infinity 32e and HD70e are for external mounting only. The unit is classed as a

7INSTALLATION INSTRUCTIONS - CONNECTIONS Water Supply. Where the water supply pressure exceeds 12 bar, an approved pressure reducing device is requir

8DimeJLHHKFInsion Terminal Position Distance A Directly below an opening, air brick, opening windows, etc. 300mm B Above an opening, air brick , op

9DIMENSIONS